Inspector Machined Parts
Listed on 2026-01-11
-
Manufacturing / Production
Quality Engineering, Manufacturing Production
Join to apply for the Inspector Machined Parts role at Lockheed Martin
Onsite Full-time:
The work associated with this position will be performed onsite at a designated Lockheed Martin facility.
Perform diversified visual and dimensional inspection operations on less complex first run/or sampling on a wide range of more complicated standard machined, welded, and composite vendor parts and assemblies.
ResponsibilitiesFrom drawings, specifications, manuals, operation sheets, purchase orders, general instructions, standard procedures, and recognized methods to inspect a variety of vendor supplied and in-plant produced parts and assemblies, or to inspect, after any operation or upon completion of complex standard and less complicated first run machined parts.
Follow general instructions, complex drawings, machine manuals, special instructions, and standard inspection methods and procedures.
Inspect less complicated parts and assemblies before, during and after release for overhaul and repair operations.
Determine proper inspection methods and sequence, select most effective measuring instruments, holding devices, and other inspection equipment, and make all necessary mathematical computations.
Plan and perform standard surface plate and dividing head layouts and dimensionally check diameters, locations, width, length, depth, hole sizes, heights, spacing, concentricitys, parallelisms, compound angles, etc. using vernier calipers, height gage, dial indicators, size blocks, and other precision measuring instruments, as applicable.
Utilize coordinate measuring machine (CMM) to perform inspection operations on vendor and in-house manufactured parts.
Perform complex set-ups under the guidance of a senior operator.
Check parts for nicks, scratches, cracks, burns, dents, shape edges, rust, corrosion, proper material, hardness, process, finish, heat treat, contours, welding, brazing, identification marking, and evidence of previous source inspections.
As applicable check for completeness of operation and other defects, discrepancies, and surface irregularities.
Prepare all necessary inspection reports and complete all other inspection paperwork as required.
Perform other related duties consistent with parts inspection as directed.
Refer unusual conditions, recurring discrepancies or difficult problems to senior inspector, working leader or supervisor.
Perform operator checklist as required.
Contribute to the overall effectiveness of equipment by performing operator required upkeep.
Follow all rules and regulations pertaining to environmental health and safety.
Segregate waste material and follow good housekeeping practices.
QualificationsDesired Skills
Work from drawings, specifications, manuals, operation sheets, purchase orders, general instructions, standard procedures, and recognized methods to inspect a variety of vendor supplied and in-plant produced parts and assemblies, or to inspect, after any operation or upon completion of complex standard and less complicated first run machined parts.
Follow general instructions, complex drawings, machine manuals, special instructions, and standard inspection methods and procedures.
Determine proper inspection methods and sequence, select most effective measuring instruments, holding devices, and other inspection equipment, and make all necessary mathematical computations.
Plan and perform standard surface plate and dividing head layouts and dimensionally check diameters, locations, width, length, depth, hole sizes, heights, spacing, concentricitys, parallelisms, compound angles, etc. using vernier calipers, height gage, dial indicators, size blocks, and other precision measuring instruments, as applicable.
2 to 3 years or Sikorsky experience
Other Important InformationBy applying to this job, you are expressing interest in this position and could be considered for other career opportunities where similar skills and requirements have been identified as a match. Should this match be identified you may be contacted for this and future openings.
Ability to work remotely Onsite Full-time:
The work associated with this position will be performed onsite at a designated Lockheed Martin facility.
- Entry level
- Full-time
- Engineering and Information Technology
- Industries
- Defense and Space Manufacturing
Referrals increase your chances of interviewing at Lockheed Martin by 2x
Sign in to set job alerts for “Inspector” roles.Quality Inspector Level 3 for 2nd and 3rd shift
We’re unlocking community knowledge in a new way. Experts add insights directly into each article, started with the help of AI.
#J-18808-Ljbffr(If this job is in fact in your jurisdiction, then you may be using a Proxy or VPN to access this site, and to progress further, you should change your connectivity to another mobile device or PC).